--- dovecot-1.0.beta2/doc/mkcert.sh.configfile	2006-01-16 21:14:54.000000000 +0100
+++ dovecot-1.0.beta2/doc/mkcert.sh	2006-01-26 14:28:38.000000000 +0100
@@ -29,6 +29,7 @@
 fi
 
 $OPENSSL req -new -x509 -nodes -config $OPENSSLCONFIG -out $CERTFILE -keyout $KEYFILE -days 365 || exit 2
-chmod 0600 $KEYFILE
+chown root:root $CERTFILE $KEYFILE
+chmod 0600 $CERTFILE $KEYFILE
 echo 
 $OPENSSL x509 -subject -fingerprint -noout -in $CERTFILE || exit 2
--- dovecot-1.0.beta2/dovecot-example.conf.configfile	2006-01-22 12:32:52.000000000 +0100
+++ dovecot-1.0.beta2/dovecot-example.conf	2006-01-26 14:31:23.000000000 +0100
@@ -5,17 +5,14 @@
 # value inside quotes, eg.: key = "# char and trailing whitespace  "
 
 # Default values are shown after each value, it's not required to uncomment
-# any of the lines. Exception to this are paths, they're just examples
-# with real defaults being based on configure options. The paths listed here
-# are for configure --prefix=/usr --sysconfdir=/etc --localstatedir=/var
-# --with-ssldir=/etc/ssl
+# any of the lines.
 
 # Base directory where to store runtime data.
 #base_dir = /var/run/dovecot/
 
 # Protocols we want to be serving:
 #  imap imaps pop3 pop3s
-#protocols = imap imaps
+protocols = imap imaps pop3 pop3s
 
 # IP or host address where to listen in for connections. It's not currently
 # possible to specify multiple addresses. "*" listens in all IPv4 interfaces.
@@ -24,11 +21,11 @@
 # for each service, you will need to configure these settings inside the
 # protocol imap/pop3 { ... } section, so you can specify different ports
 # for IMAP/POP3.
-#listen = *
+listen = [::]
 
 # IP or host address where to listen in for SSL connections. Defaults
 # to above if not specified.
-#ssl_listen =
+ssl_listen = [::]
 
 # Disable SSL/TLS support.
 #ssl_disable = no
@@ -37,8 +34,8 @@
 # dropping root privileges, so keep the key file unreadable by anyone but
 # root. Included doc/mkcert.sh can be used to easily generate self-signed
 # certificate, just make sure to update the domains in dovecot-openssl.cnf
-#ssl_cert_file = /etc/ssl/certs/dovecot.pem
-#ssl_key_file = /etc/ssl/private/dovecot.pem
+ssl_cert_file = /etc/pki/dovecot/certs/dovecot.pem
+ssl_key_file = /etc/pki/dovecot/private/dovecot.pem
 
 # If key file is password protected, give the password here. Alternatively
 # give it when starting dovecot with -p parameter.
@@ -351,8 +348,8 @@
 # in is important to avoid deadlocks if other MTAs/MUAs are using multiple
 # locking methods as well. Some operating systems don't allow using some of
 # them simultaneously.
-#mbox_read_locks = fcntl
-#mbox_write_locks = dotlock fcntl
+mbox_read_locks = fcntl
+mbox_write_locks = fcntl
 
 # Maximum time in seconds to wait for lock (all of them) before aborting.
 #mbox_lock_timeout = 300